P-02 High-Solids Waterborne Acrylic Block Filler
P-02 is a high-solids acrylic latex block filler for concrete block, cinder block and precast concrete.
Made to order
Overview
P-02 is a high-solids acrylic latex block filler for concrete block, cinder block and precast concrete. Its job is to force material into the open pores and bug holes of masonry and leave a continuous, pinhole-free surface that a finish coat can be applied over uniformly.
Uses and Benefits
Concrete masonry unit (CMU): standard, lightweight and split-face block. Cinder block and precast concrete. Poured concrete walls with bug holes and surface voids. Under high-performance topcoats (epoxies and urethanes) as well as architectural finishes.
Limitations
Not a waterproofer. Do not use below grade as a hydrostatic barrier or in immersion service. Do not apply over existing coatings: a coating already bridging the voids defeats the fill, and peeling may result. Do not apply to damp, wet or smooth, slick surfaces. Surface pH must be at or below 10. Minimum 28-day substrate cure. Do not apply below 50°F (air, surface and material), and keep at least 5°F above the dew point. High humidity extends dry and recoat times at this film build. PROTECT FROM FREEZING: waterborne, a frozen container is scrap.
Preparation
Surface must be clean, dry and sound. Remove all oil, dust, grease, dirt, loose rust, laitance, efflorescence, salts, form release agents, curing compounds and other foreign matter. Masonry must be dry before coating, with moisture content at or below 15%. New Concrete & Masonry: Minimum 28-day cure. Prepare per SSPC-SP13 / NACE No. 6 or ICRI Guideline No. 310.2R-2013 to CSP 1–3. Remove contaminants by sandblasting, shotblasting, mechanical scarification or suitable chemical means per ASTM D4260. Rinse thoroughly and allow to dry completely. Existing Concrete & Masonry: Prepare as new. Remove oils, grease and chemical contamination with a strong detergent per ASTM D4258. Remove mildew before coating; it is a fungus that will grow through a new coat. Do not apply over smooth, slick surfaces or existing coatings; peeling may result. Any preparation short of total removal of an old coating may shorten the service life of the system. Surface pH: Test the prepared surface. P-02 requires a surface pH of less than 10.
Key Benefits
- Inquire
Technical Data
At a glance: the specs most teams decide on.
- Shore Hardness @ 24 Hours
- 20Warmer temperatures will increase hardness
- Shore Hardness @ 7 Days
- 40Warmer temperatures will shorten time to reach full hardness
- Gloss @ 60° Angle
- Flat
- Solids by Volume (Mixed)
- 46%
- Dry to Touch
- 1–2 hoursWarmer temperatures will reduce time and colder temperatures will increase time
- Through Dry
- 1 HourWarmer temperatures will reduce time and colder temperatures will increase time
- Dry to Lightly Use
- 24 HoursWarmer temperatures will reduce time and colder temperatures will increase time
- Full Cure
- 5 daysWarmer temperatures will reduce time and colder temperatures will increase time
- Number of Components
- 1
- Mixed Viscosity @ 25°C/77°F
- 110 KU (ASTM D2196)Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
- Ideal Application Temperature
- 50°F minimum; at least 5°F above dew pointVerify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
- Application Thickness
- 7–10 mils dry (16–20 mils wet)
- Odor
- SubtleMeasuring odor offensiveness is difficult so experience with chemicals has been consulted here
- Storage Temperature
- 60–80°FStore material between 60-90 degrees F in a protected dry location.
Colors & Packaging
Colors
Tap a color to enlarge. Swatches are a representative guide. Request a physical sample for color-critical work.
Packaging
- Available sizes
- 5 Gallons
- Note
- Made to order
Where It's Used
Used in Systems
Mixing & Application
P-02 is supplied ready to use. Stir thoroughly before and during application without whipping air into the material. Reduce with clean water up to 15% only if atomization requires it.
Disposal: Dispose of material, containers, solvents, etc. per Federal, State and local guideline, rules and laws
More Wall Products
Related products
Complete the system or compare close alternatives in the same family.
Made in the USA · Tech Support Included
Need P-02 for your project?
Our team will help you spec the right system, quantities, and colors, and get you a quote fast.