Category:
F-11 TDK
F-11 TDK Clear Epoxy Trowel Mortar
About the product
Product Overview
F-11 TDK combines our clear, nonylphenol-free, epoxy resin (E1), our blended cycloaliphatic reactant (H1.5) and our Trowel Aggregate PN 1324 to create the easiest troweling material available anywhere. This combination achieves an easily closed, natural, epoxy mortar that can be walked on within a few hours. The cured material has high compressive strength (three times that of concrete) , great impact resistance and a broad range of resistance to chemical attack. It is virtually odor-free.
Uses
F-11 TDK is primarily used as an economical, natural colored, fast setting epoxy overlay to protect and/or repair concrete. Because it is a mortar, it is the ideal material for sloping floors and creating ramps and transitions. It can also be used to fill deep pits, cracks and voids in concrete floors and walls.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
F-11 TDK
Category
Kit Yield in Gallons
N/A
3 quart kit (liquids)
1 x 45 lb. bag of aggregate
Number of Mixes Per Kit
N/A
N/A
Number of Components
N/A
N/A
Mix Ratio Liquids by Volume
0.5 gal A, 0.25 gal B, 45 lb. C
Accuracy when mixing kits from bulk containers is critical. For mix ratio by weight contact Lab@polymerNation.com.
Ideal Application Temperatures
60F-90F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
350-450 cP25°C/77°F (A&B)
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
15 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
1 Hour
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
3 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
4 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
12 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
7 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
D65
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
D78
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
25-30
Not top coated. See Gloss data for selected top coat if required
VOC’s of Mixed Material
<50g/L
EPA Method 24
Color Scale per ASTM D1500
.5-1.0
Clear to slightly amber
Solids by Volume Mixed
100%
N/A
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
N/A
Application Thickness in Mils
N/A
N/A
Coverage Per Mix
Each mix will cover 23 sq. ft. at 1/4″ theoretical coverage. A waste factor of 10-15% should be contemplated
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
N/A
Available Colors
Clear & Color Packs
N/A
Mixing & Installation
A mixture consists of .5 gal A, .25 gal B and 45 LB. of C (PN 1324). Combine part A and B into a single container, large enough to accept the entire kit (1 mix equals 3.7 gallons when Part C is added). Premix liquids at 350 RPM for 1 minutes using an appropriate mixing blade or mixing machine. Pour Part C into the mixed resin and continue mixing until a homogenous mortar is achieved (2-3 minutes usually). Pour material on floor and spread to desired thickness using a screed rake or pour material into a screed box. Follow using good hand or power trowel techniques. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
Product Documentation
PRODUCT PDF.png)
.png)
